Hi: Here is a picture of what you are looking for. It's Here are the directions to replace it. The Vehicle Speed Sensor (VSS) is a magnetic pick-up sensor that sends a signal to the Powertrain Control Module (PCM) and the speedometer. The sensor measures the rotation of the output shaft on the transaxle and sends an AC voltage signal to the PCM which determines the corresponding vehicle speed. TESTING Disconnect the negative battery cable.

Sep 26, 2018 - TOYOTA. HARRIER Factory Service. Manual (pdf version). 1MZ-FE 3.0L V6. 2016 Toyota Harrier Repair. - authenticedmontonoilers. 2016 toyota harrier repair manual pdf.

1. Ford Wheel Speed Sensor
2. Ford Transmission Speed Sensor Location
3. Ford Speed Sensor Location

Disengage the wiring harness connector from the VSS. Using a Digital Volt-Ohmmeter (DVOM), measure the resistance (ohmmeter function) between the sensor terminals. If the resistance is 190-250 ohms, the sensor is okay. REMOVAL & INSTALLATION Disconnect the negative battery cable. On a manual transaxle equipped vehicle: Remove the air cleaner assembly.

On a automatic transaxle equipped vehicle: Raise and support the vehicle. Unplug the VSS electrical connector. Remove the speedometer cable (early models only). Remove the retaining bolt from the VSS. Lift the VSS out of the transaxle. Remove the driven gear retainer and the drive gear.

To install: Inspect the O-ring on the sensor and replace if necessary. Install the driven gear and the retainer. Place the VSS into the transaxle.

Tighten the retaining bolt to 43-53 inch lbs. Install the speedo cable (if necessary). Attach the VSS electrical connector. On a manual transaxle equipped vehicle: Install the air cleaner assembly.

Ford Wheel Speed Sensor

On a automatic transaxle equipped vehicle: Lower the vehicle. Connect the negative battery cable. I hope this helps.

Let me know if you have other questions.

The vehicle speed sensor is located on transaxle in behind the engine. Tricky to get at and not an easy replacement. While it is possible the sensor is bad, the more common issue with your Windstar is the speedometer itself. You should have it properly diagnosed before replacing parts.

If the speedometer is the defect you will need to replace the instrument panel as an assembly. Using parts from a recycler will often result with another bad speedometer as it is a very common problem. Some aftermarket auto supply may be able to get you a rebuilt unit. If not you may have to get it from Ford. Jul 29, 2010.

Hyundai VSS locations: On 1999-2003 vehicles, the vehicle speed sensor is built into the speedometer. On 2004-2005 vehicles, the vehicle speed sensor is attached to the output shaft of the transaxle. On 1996-2003 vehicles, the vehicle speed sensor is built into the speedometer. On 2004-2005 vehicles, the vehicle speed sensor is attached to the output shaft of the transaxle. On 1999-2003 vehicles, the vehicle speed sensor is built into the speedometer. On 2004-2005 vehicles, the vehicle speed sensor is attached to the output shaft of the transaxle.

Ford Transmission Speed Sensor Location

Hope helps (remember rated this). Jul 14, 2010.

Manual transmission The vehicle speed sensor (speedometer gear), which is located on the transaxle, serves as the manual transaxle's dipstick. Park the car on a level surface, turn the engine OFF and apply the parking brake. Locate the speedometer cable assembly where it enters the transaxle. Unplug the electrical connection from the vehicle speed sensor (speedometer gear). Disconnect the speedometer cable from the speed sensor.

Wipe the area around the speed sensor with a clean rag, then loosen the speed sensor retaining bolt. Gently pry the speed sensor from the transaxle. 1: Location of the manual transaxle's fluid level marks — 1.8L engine Fig.

2: Location of the manual transaxle's fluid level marks — 1.9L and 2.0L engines. Check the condition of the speed sensor O-ring and replace it if it is damaged. Check the fluid level on the speed sensor as illustrated.

If the level is low, place a funnel in the speed sensor hole. Add the specified fluid to the transaxle until the FULL level is reached. Do not overfill the transaxle. Install the speed sensor and tighten the retaining bolt to 69–104 inch lbs. Connect the speedometer cable. Engage the speed sensor electrical connection. 3: If necessary, add transmission fluid through a funnel into the speed sensor opening Jul 12, 2010.

Ford Speed Sensor Location

The Vehicle Speed Sensor is located on transaxle, at the rear of the engine. I would check the harness connector to be sure it is clean and connected tightly.

Also check the wiring for cuts and chaffing. Since it is fairly inexpensive, only about $42.00 from Ford, you may want to consider replacing it, at least to eliminate it as a possibility. You may want to go to a muffler shop to have this done like speedy, I believe the flex pipe needs to be undone to get to the VVS. If there is an Auto Zone around your area, you could always ask them for the step by step instructions to replacing the VVS, and it's free of charge. Good luck and hope this helps. Jun 11, 2009.